Hvr-m25e manual




















Page Does not light up while the unit is not loading a In addition to Remote Commander supplied with the cassette. Commander whose command mode is set to VTR4. Index is useful when you search for scenes on a tape. During rewind, the picture does consumer DV format.

Only SP recording mode is not appear on the monitor. Page Location and Function of Parts 3 Audio control section During normal recording, sounds are recorded onto channels 1 and 2; they cannot be recorded onto channels 3 and 4. During audio dubbing, sounds are dubbed onto channels 3 and 4. LINK indicator 1 HDV indicator 3 60 indicator Lights when the unit is in the following operating Lights when the unit is in the following operating status.

LINK standard. Page Displaying Various Data The unit can display various superimposed text data on Data display the built-in LCD monitor and also an external monitor You can confirm important information for normal connected to the unit. In such a case, if you insert the cassette forcibly, the cassette Connect the power cord supplied to the AC IN may not be loaded properly or malfunctions may connector. Page Notes on Power Supply and Video Cassettes On recording Note on playback on other equipment A tape recorded in HDV format with the unit cannot be You cannot record or output EE signals and any played back with the devices not compatible with software having copyright protection signals on the HDVi format.

Page Connections For Playback Playback This section describes the connections and settings for the playback and functions such as playback at various speeds and searching for a specific scene on a recorded tape. Connections for Playback Connecting the unit to a monitor without an i. LINK jack You can connect the unit to video monitor without an i. LINK jack. Page Playback Functions HD video camera recorder. Page 1 minute, the unit Notes begins to play back at normal speed.

Page For duplicating Data display screen. Chapter 2 Playback and Recording At the preset time, the power of the unit turns on, and after a few to several ten seconds, AUTO is displayed on Data display screen page Page Using the Unit as a Videocassette Recorder This section describes the connections, settings and operations necessary to perform recording on the unit. The same settings and operations apply whether you are using the unit for dubbing.

By connecting the unit to an external AC timer not supplied , you can start recording at a preset time. To reset the time code The following menus are displayed.

The following menus are displayed. LINK jack This section describes the connections and settings necessary to perform dubbing on other equipment, Monitor HVR-M25 rear panel using the unit as a video player. Prepare the unit. LINK format during duplication, the portion where the connection. Page Duplication generating a work tape with the same time code Duplicating a series of tapes Detecting a blank portion during duplication While pausing duplication mode, you can change the tape on the player.

Therefore, you can duplicate a If the unit detects a blank portion on the source tape series of tapes on a single tape. Page Clean the video heads with the supplied cleaning cassette see page Dirty video head. Use a cleaning cassette. Note When a warning message other than above is displayed, consult your Sony dealer. Chapter 4 Dubbing to another equipment using i. Press STOP button. LINK cable to a computer jack on the unit. If you connect the i.

Also, you may select color bars with or without tone signals 1 kHz full bit —20 dB at 60i, 1 kHz full bit —18 dB at 50i. OFF : Does not display color bars and no tone signals. For details, see page Remote Commander is disabled.

Reboots after change. Page Troubleshooting Adjust the menu again. To prevent this incident recurring, do not pull out the plug while adjusting the menu or the brightness of LCD monitor. The remaining tape time is not displayed. LINK, the user bit is not displayed correctly. Css t Condensation has occurred.

Remove the cassette and insert it again after approximately 1 hour page Page Alarm Messages Warning indicators and messages Alarm Messages The following alarm messages will appear together with the alarm indicators. Take corrective action according to the displayed message. Eject the cassette. Page Notes On Use Notes on Use Clean the cabinet with a soft dry cloth Notes on the Videocassette When the cabinet is very dirty, clean it with a soft dry Recorder cloth lightly moistened with a mild detergent solution and finish it with a dry cloth.

Do not use the unit in a place subject to direct sunlight or heat sources Do not put magnetic objects close to the unit Please consult your Sony dealer. Page Notes On Lcd Screen Cleaning the terminal About Moisture Condensation If the gold-plated terminals of a cassette become dirty, or dirt accumulates on the terminals, the correct If the unit or cassette is brought directly from a cold to remaining tape time may not be displayed.

It applies the same cassette, tape speed, and track pitch as DV format. Only playback of a tape Only playback of a tape Some equipment cannot Page Recording tape when the unit is used as a recorder Menu item i. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance.

The model number and the serial number are located at the name plate on the left of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Replace only with part num- ber specified. Replace only with the same or equivalent type. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.

Look for parts which, though functioning, show obvious signs of deterioration. Check the line cord for cracks and abrasion. Recommend the replacement of any such line cord to the customer. Check leakage as described below. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Caution: The printed pattern copper foil may peel away if the heated tip is applied for too long, so be careful!



0コメント

  • 1000 / 1000